Set up Wireless on AP FiberHome HG180Ev2

  1. Type 192.168.2.1 in URL and enter Username : admin / Password : enter letters from below picture then press Login.  If enter wrong password 3 times, there'll be a message to wait for 1 minute then re-enter password and Login.  If don't want to wait, ture off/ on AP 1 time and re-Login
  2. Basic Setup : Basic Setup > WLAN
    • Basic Configuration 2.4GHz
      • Enable WLAN : tick a check to enable
      • Enable SSID : tick a check to enable only SSID1 (choose to enable-disable SSID1-4 Firmware not other SSID)
      • Hide SSID : not set but if want to hide SSID, tick a check
      • SSID : enter preferred name
      • press Apply
    • Basic Configuration 5GHz
      • Enable WLAN : tick a check to enable
      • Enable SSID : tick a check to enable only SSID1 (choose to enable-disable SSID1-4 Firmware not other SSID)
      • Hide SSID : not set but if want to hide SSID, tick a check
      • SSID : enter preferred name
      • press Apply
    • Security Setting 2.4GHz
      • Authentication : default setting is WPA-PSK/WPA2-PSK MIXED that can be changed
      • WPA Preshare key : contain 8-32 characters
      • Encryption Mode : choose encryption type
      • Click here to display 
      • press Apply
    • Security Setting 5GHz
      • Authentication : default setting is WPA-PSK/WPA2-PSK MIXED that can be changed
      • WPA Preshare key : contain 8-32 characters
      • Encryption Mode : choose encryption type
      • Click here to display 
      • press Apply
  3. Advanced Setup : Advanced Setup > WLAN
    • Advanced Configuration 2.4GHz
      • Mode : choose mode per compatible device (default is 802.11b/g/n)
      • Bandwidth : default is 20, if choose 40, connected device should support 802.11n (must choose Mode with n to be usable)
      • Channel : choose preferred CH (default is Auto)
      • press Apply to save the settings
    • Advanced Configuration 5GHz
      • Mode : choose mode per compatible device (default is 802.11b/g/n)
      • Bandwidth : choose Bandwidth to use (default is Auto)
      • Channel : choose preferred CH (default is Auto)
      • press Apply to save the settings
    • WPS Configuration 2.4GHz (iOS is incompatible)
    • Press Button
      • Enable WPS : tick a check to enable (default is enable)
      • Choose AP Role : Registrar is to press WPS button at AP
      • Press WPS Button : PBC is identified as pressing WPS button at AP, afterward AP will wait for device connection for 2 seconds, WPS LED will flash and when successfully connected WPS LED will be off (Android, go to > Setting > WiFi > Advance > WPS Push Button)
      • Input PIN Number : enter PIN generated from Smart Phone or device and press PIN, those devices and AP are connected
      • Negotiation Status : while AP is waiting device to connect, it’ll show status PROCESSING, after successfully connected, its status is OK
      • press Apply
      • Refresh : press to check Negotiation Status
    • PIN
      • Enable WPS : tick a check to enable (default is enable)
      • Choose AP Role : if want to use PIN, choose Enrollee (default is Registrar)
      • Current PIN : on connected device choose AP’s network name and then enter the displayed PIN, if want to change PIN, press Generate New PIN
      • Session Status : PIN input process, session status is PROCESSING
      • After connected, session status is OK
      • press Apply
      • Refresh : press to check Session Status
    • WPS Configuration 5GHz (iOS is incompatible)
    • Press Button
      • Enable WPS :  tick a check to enable (default is enable)
      • Choose AP Role : Registrar is to press WPS button at AP
      • Press WPS Button : PBC is identified as pressing WPS button at AP, afterward AP will wait for device connection for 2 seconds, WPS LED will flash and when successfully connected WPS LED will be off (Android, go to > Setting > WiFi > Advance > WPS Push Button)
      • Input PIN Number : enter PIN generated from Smart Phone or device and press PIN, those devices and AP are connected
      • Negotiation Status : while AP is waiting device to connect, it’ll show status PROCESSING, after successfully connected, its status is OK
      • press Apply
      • Refresh : press to check Negotiation Status
    • PIN
      • Enable WPS : tick a check to enable (default is enable)
      • Choose AP Role : if want to use PIN, choose Enrollee (default is Registrar)
      • Current PIN : on connected device choose AP’s network name and then enter the displayed PIN, if want to change PIN, press Generate New PIN
      • Session Status : PIN input process, session status is PROCESSING
      • After connected, session status is OK
      • press Apply
      • Refresh : press to check Session Status
Download File

Was this helpful?

Very bad Very Good