Set up Wireless on AP FiberHome HG180Ev2
- Type 192.168.2.1 in URL and enter Username : admin / Password : enter letters from below picture then press Login. If enter wrong password 3 times, there'll be a message to wait for 1 minute then re-enter password and Login. If don't want to wait, ture off/ on AP 1 time and re-Login
- Basic Setup : Basic Setup > WLAN
- Basic Configuration 2.4GHz
- Enable WLAN : tick a check to enable
- Enable SSID : tick a check to enable only SSID1 (choose to enable-disable SSID1-4 Firmware not other SSID)
- Hide SSID : not set but if want to hide SSID, tick a check
- SSID : enter preferred name
- press Apply
- Basic Configuration 5GHz
- Enable WLAN : tick a check to enable
- Enable SSID : tick a check to enable only SSID1 (choose to enable-disable SSID1-4 Firmware not other SSID)
- Hide SSID : not set but if want to hide SSID, tick a check
- SSID : enter preferred name
- press Apply
- Security Setting 2.4GHz
- Authentication : default setting is WPA-PSK/WPA2-PSK MIXED that can be changed
- WPA Preshare key : contain 8-32 characters
- Encryption Mode : choose encryption type
- Click here to display
- press Apply
- Security Setting 5GHz
- Authentication : default setting is WPA-PSK/WPA2-PSK MIXED that can be changed
- WPA Preshare key : contain 8-32 characters
- Encryption Mode : choose encryption type
- Click here to display
- press Apply
- Basic Configuration 2.4GHz
- Advanced Setup : Advanced Setup > WLAN
- Advanced Configuration 2.4GHz
- Mode : choose mode per compatible device (default is 802.11b/g/n)
- Bandwidth : default is 20, if choose 40, connected device should support 802.11n (must choose Mode with n to be usable)
- Channel : choose preferred CH (default is Auto)
- press Apply to save the settings
- Advanced Configuration 5GHz
- Mode : choose mode per compatible device (default is 802.11b/g/n)
- Bandwidth : choose Bandwidth to use (default is Auto)
- Channel : choose preferred CH (default is Auto)
- press Apply to save the settings
- WPS Configuration 2.4GHz (iOS is incompatible)
- Press Button
- Enable WPS : tick a check to enable (default is enable)
- Choose AP Role : Registrar is to press WPS button at AP
- Press WPS Button : PBC is identified as pressing WPS button at AP, afterward AP will wait for device connection for 2 seconds, WPS LED will flash and when successfully connected WPS LED will be off (Android, go to > Setting > WiFi > Advance > WPS Push Button)
- Input PIN Number : enter PIN generated from Smart Phone or device and press PIN, those devices and AP are connected
- Negotiation Status : while AP is waiting device to connect, it’ll show status PROCESSING, after successfully connected, its status is OK
- press Apply
- Refresh : press to check Negotiation Status
- PIN
- Enable WPS : tick a check to enable (default is enable)
- Choose AP Role : if want to use PIN, choose Enrollee (default is Registrar)
- Current PIN : on connected device choose AP’s network name and then enter the displayed PIN, if want to change PIN, press Generate New PIN
- Session Status : PIN input process, session status is PROCESSING
- After connected, session status is OK
- press Apply
- Refresh : press to check Session Status
- WPS Configuration 5GHz (iOS is incompatible)
- Press Button
- Enable WPS : tick a check to enable (default is enable)
- Choose AP Role : Registrar is to press WPS button at AP
- Press WPS Button : PBC is identified as pressing WPS button at AP, afterward AP will wait for device connection for 2 seconds, WPS LED will flash and when successfully connected WPS LED will be off (Android, go to > Setting > WiFi > Advance > WPS Push Button)
- Input PIN Number : enter PIN generated from Smart Phone or device and press PIN, those devices and AP are connected
- Negotiation Status : while AP is waiting device to connect, it’ll show status PROCESSING, after successfully connected, its status is OK
- press Apply
- Refresh : press to check Negotiation Status
- PIN
- Enable WPS : tick a check to enable (default is enable)
- Choose AP Role : if want to use PIN, choose Enrollee (default is Registrar)
- Current PIN : on connected device choose AP’s network name and then enter the displayed PIN, if want to change PIN, press Generate New PIN
- Session Status : PIN input process, session status is PROCESSING
- After connected, session status is OK
- press Apply
- Refresh : press to check Session Status
- Advanced Configuration 2.4GHz